TD aux. coolant pump
Moderator: Fatmobile
I would be interested to know if anyone has checked the euro wiring diagram for the aux pump. Mine was disconnected when I got the motor but I do have an unused temp sensor near the head outlet. Of the three basic options: run pump when cold, run when hot, don't run at all, what's the consensus?
I have a thermostatically controlled oil/air cooler so I don't need the aux pump for cooling ...
Thanks!
I have a thermostatically controlled oil/air cooler so I don't need the aux pump for cooling ...
Thanks!
Correct. The pump is wired to run a short burst when the ignition is turned on, then is thermocontrolled to run above 107 deg C and lastly to run after ignition is turned off to prevent hot spots.caveman wrote:I'm pretty sure all those pumps were used for an after run i.e. they would turn on after the vehicle was turned off in order to circulate coolant in the system so not to create any hot spots etc. they were installed in any vehicle where high load / high performance / hot under hood temps were involved. i would try to find a euro spec wiring diagram to see if it's not switched on that way
And Here's the wiring:
Johann
83.5 Westy 1.6 TD
93 1.9TD engine in the shed
93 1.9TD engine in the shed
Thanks a lot Johann!
That's exactly what I needed. Do you have the entire Transporter turbodiesel manual? I would like to try and find a copy.
Here are some pics from my recent '86 GL to 1.6TD conversion ...
http://pages.cthome.net/rasminko/overall.jpg
http://pages.cthome.net/rasminko/turbo1.jpg
http://pages.cthome.net/rasminko/pspump1.jpg
http://pages.cthome.net/rasminko/pspump3.jpg
http://pages.cthome.net/rasminko/intake.jpg
I've since added an intercooler but don't have pics of that yet.
Good luck w/ your conversion ...
Reiney
That's exactly what I needed. Do you have the entire Transporter turbodiesel manual? I would like to try and find a copy.
Here are some pics from my recent '86 GL to 1.6TD conversion ...
http://pages.cthome.net/rasminko/overall.jpg
http://pages.cthome.net/rasminko/turbo1.jpg
http://pages.cthome.net/rasminko/pspump1.jpg
http://pages.cthome.net/rasminko/pspump3.jpg
http://pages.cthome.net/rasminko/intake.jpg
I've since added an intercooler but don't have pics of that yet.
Good luck w/ your conversion ...
Reiney
-
- Diesel Freak
- Posts: 199
- Joined: Sun Nov 13, 2005 2:53 pm
- Location: Montreal, QC, and StJohn's, Nfld, Canada
Ok folks please excuse me if you've heard this one before but I have been churning this one over... even before this thread.
If I had one of those pumps I would try to use it in combination with my on board furnace as a block heater.
There are two options for this:
One is to make a manifold/ loop for the coolant and wrap it around the inner shell of the furnace and pump the water to and from the heater core line. (like the syncro but using the air furnace)
or the more elegant slightly less efficient (in terms of btu transfered) way would be to use the heater core as the exchanger for the engine. I think there might be some mods required in the air / heater box for this but I would use the pump in line with the heater core (front) so that the furnace is heating the coolant in the core as it goes though to heat you! Am I making sense? The idea is actually VW's (I think) since this seems to be how the syncro's aux. heaters work.
If I had one of those pumps I would try to use it in combination with my on board furnace as a block heater.
There are two options for this:
One is to make a manifold/ loop for the coolant and wrap it around the inner shell of the furnace and pump the water to and from the heater core line. (like the syncro but using the air furnace)
or the more elegant slightly less efficient (in terms of btu transfered) way would be to use the heater core as the exchanger for the engine. I think there might be some mods required in the air / heater box for this but I would use the pump in line with the heater core (front) so that the furnace is heating the coolant in the core as it goes though to heat you! Am I making sense? The idea is actually VW's (I think) since this seems to be how the syncro's aux. heaters work.
Yea,
I thought about doing exactly this using a 3-6 gallon RV hot water heater with the valves necessary to route the domestic hot water through a flat plate heat exchanger. Probably would need another of those small pumps for the domestic loop. Or, you could cut a hole in the hot water heater tank and put a copper coil in there.
My ultimate goal is propane-fired domestic hot water with a way to use this as an engine heater. Oh, yea, I need to heat a WVO tank as well ...
Still workin' this all out ...
Reiney
I thought about doing exactly this using a 3-6 gallon RV hot water heater with the valves necessary to route the domestic hot water through a flat plate heat exchanger. Probably would need another of those small pumps for the domestic loop. Or, you could cut a hole in the hot water heater tank and put a copper coil in there.
My ultimate goal is propane-fired domestic hot water with a way to use this as an engine heater. Oh, yea, I need to heat a WVO tank as well ...
Still workin' this all out ...
Reiney
I don't have the whole manual. I got these pages from a guy in Scotland I was sourcing parts from.Reiney wrote:Thanks a lot Johann!
That's exactly what I needed. Do you have the entire Transporter turbodiesel manual? I would like to try and find a copy.
Reiney
Does anyone have any thoughts on a local (North American) source for a similar coolant pump? Maybe a 12V fish tank circulator or from another vehicle?
Johann
83.5 Westy 1.6 TD
93 1.9TD engine in the shed
93 1.9TD engine in the shed
I don't have the whole manual. I got these pages from a guy in Scotland I was sourcing parts from.Reiney wrote:Thanks a lot Johann!
That's exactly what I needed. Do you have the entire Transporter turbodiesel manual? I would like to try and find a copy.
Here are some pics from my recent '86 GL to 1.6TD conversion ...
http://pages.cthome.net/rasminko/overall.jpg
http://pages.cthome.net/rasminko/turbo1.jpg
http://pages.cthome.net/rasminko/pspump1.jpg
http://pages.cthome.net/rasminko/pspump3.jpg
http://pages.cthome.net/rasminko/intake.jpg
I've since added an intercooler but don't have pics of that yet.
Good luck w/ your conversion ...
Reiney
Reiney, is that a K3 Turbo on there? It doesn't seem to have any clearance issues with the LS motor mount. Correct?
I carefully rebuilt the K24 that came with my engine but have since come into 2 K3s although both are in need of some work. Arrgh. Anyone want to buy a rebuilt K24?
Regarding the coolant pump, does anyone have any thoughts on a local (North American) source? Maybe a 12V fish tank circulator or one from another vehicle?
Johann
83.5 Westy 1.6 TD
93 1.9TD engine in the shed
93 1.9TD engine in the shed
Summit Racing, (http://summitracing.com) has electric water pumps but they're pricey .. $200-$300 and the ones in my catalog are all designed to bolt on to Chevys and Fords.
You might be able to use a 12V circulator pump designed for solar-powered heating systems. These can handle fluids up to 250 deg.F and move 3 - 6 gpm. I have access to these from one of my suppliers but they're not cheap either; usually around $175 - $275.
Might still be able to get the VW OEM pump; I can look for a part number on mine if you need it ...
R.
You might be able to use a 12V circulator pump designed for solar-powered heating systems. These can handle fluids up to 250 deg.F and move 3 - 6 gpm. I have access to these from one of my suppliers but they're not cheap either; usually around $175 - $275.
Might still be able to get the VW OEM pump; I can look for a part number on mine if you need it ...
R.
-
- Global Moderator
- Posts: 7574
- Joined: Wed Oct 30, 2002 10:28 pm
- Location: north central Iowa
My cousin works in a diesel shop, he gave me an eletric waterpump from something, maybe a cummins. Nice and small, fits in one hand.
Maybe you can get a used one cheap.
Maybe you can get a used one cheap.
'91 Golf gasser converted to a 12mm pump, M-TDI.
'84 1.6TD Rabbit with a VNT-15 turbo, still setup to run on vegetable oil.
'84 GTI with 1.7TD pistons and intercooled.
2003 TDI wagon
2000 TDI Jetta.
'84 1.6TD Rabbit with a VNT-15 turbo, still setup to run on vegetable oil.
'84 GTI with 1.7TD pistons and intercooled.
2003 TDI wagon
2000 TDI Jetta.
Re:
As this link appears to no longer work, anyone have an idea what the modification mentioned here was?libbybapa wrote:If you are convinced you want to stay away from the oil-to-air cooler, then consider this untested modification that I proposed a couple of years ago.
http://www.vwdiesel.net/phpBB/viewtopic.php?t=2412
Andrew
Cheers,
Avo
Currently working on shoehorning a 1.6 TD out of a 1984 Jetta into a 1971 VW Camper (Hardtop)
"Huppity Hup! Rev! Rev! GO GO GO GO!"
"Huppity Hup! Rev! Rev! GO GO GO GO!"