Glow Plug Re-Wiring
Moderator: Fatmobile
Glow Plug Re-Wiring
Im going to be re-wiring my entire glow plug relay to under the hood. Anyone insterested in an article, reflect your results in the poll. When I finish this, this is where the write-up will appear. This is applicable only to an A2 model Jetta, with the two-wire temperature sensors, however, will possibly work with the older A1 models. This will also isolate the glow plug light on the dashboard, and currently, the way I'm doing it will render it unoperable until hooked up to the relay. I had to do this to bypass the water seperator sending unit.
-
- Diesel Freak
- Posts: 186
- Joined: Thu Jun 30, 2005 12:39 pm
- Location: Rosalia, WA
glow plug rewire
I do hope you can post this project.
-
- Turbo Charger
- Posts: 2085
- Joined: Mon Apr 24, 2006 4:34 pm
- Location: Gloucester; Limey-Land
Be sure to segregate the glowplug supplies for added convenience....
"I'm not here to help... I'm here to Pro-Volke"
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
-
- Turbo Charger
- Posts: 2085
- Joined: Mon Apr 24, 2006 4:34 pm
- Location: Gloucester; Limey-Land
That's interesting...
Why did you not bring flying leads all out towards #4 so that individual plugs can be checked in the 'open' area rather than including '2nd best' access point #3
Covering my rear with one of these...
"I'm not here to help... I'm here to Pro-Volke"
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
-
- Global Moderator
- Posts: 7574
- Joined: Wed Oct 30, 2002 10:28 pm
- Location: north central Iowa
glowplugs
I didn't think all 3 copper lugs and the lug on the wire from the glow plug fuse, would be able to stack up on one glowplug and still have room for the nut.
Everyone knows it's going to be the 2 hardest plugs to get at that are burnt out so 1 and 2 have jumpers on them.
I check for total current first, if it's low I can still check each plug.
To check the 4th glowplug I remove the glowplug fuse wire and the jumper from number 2 so I can check that one also.
If it's not one of those, I pull the nut on glowplug number 3... not real easy to get to but not too hard. That brings #1 glowplug jumper wire out and easy to get to.
Everyone knows it's going to be the 2 hardest plugs to get at that are burnt out so 1 and 2 have jumpers on them.
I check for total current first, if it's low I can still check each plug.
To check the 4th glowplug I remove the glowplug fuse wire and the jumper from number 2 so I can check that one also.
If it's not one of those, I pull the nut on glowplug number 3... not real easy to get to but not too hard. That brings #1 glowplug jumper wire out and easy to get to.
-
- Turbo Charger
- Posts: 2085
- Joined: Mon Apr 24, 2006 4:34 pm
- Location: Gloucester; Limey-Land
Code: Select all
I didn't think all 3 copper lugs and the lug on the wire from the glow plug fuse, would be able to stack up on one glowplug and still have room for the nut.
It always felt that there was a danger of twisting the #4 glowplug to a premature death. Not sure what SWG I used but it was slightly smaller than the supply but I ran 2 wires to each 'yellow' ring connector giving greater flexibility for less power drop.
"I'm not here to help... I'm here to Pro-Volke"
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
Be like meeee...Drive a Quantum TD
...The best work-horse after the cart...
Quantae grow on you...but Rabbits are like roses...
... girls like em ;o)
Only one Darwin, Einstein, Poe and Verne.
That is why if you listen, you will learn:
From the one and only Quantum-man,
Who sees the worms from outside of the can.
7 Quantae in 20 years; 4 dead and 3 TD's still alive [2 wagons & 1 fastback] oh and a GTD )
-
- Cetane Booster
- Posts: 98
- Joined: Wed Mar 24, 2004 8:42 pm
- Location: cascade mountains, washington
As another idea.....
I wires each glow plug individually. I use a 'power distribution block' commonly used in car stereo amplifier application to tie them all together.
Now it is super easy to check each glow plug individually for continuity.
I wires each glow plug individually. I use a 'power distribution block' commonly used in car stereo amplifier application to tie them all together.
Now it is super easy to check each glow plug individually for continuity.
'90 Ram 12V Cummins
'92 Jetta (current gas>TD swap project)
'86 Quantum Synchro SW gasser (future TD project?)
'82 Rabbit TurboDiesel Pickup (Totaled due to inattention)
'83 Quantum TurboDiesel sedan (crushed)
'82 Quantum TurboDiesel wagon (crushed)
'82 Quantum gasser (totaled by drunk driver)
'85 Quantum SW gasser (crushed)
'92 Jetta (current gas>TD swap project)
'86 Quantum Synchro SW gasser (future TD project?)
'82 Rabbit TurboDiesel Pickup (Totaled due to inattention)
'83 Quantum TurboDiesel sedan (crushed)
'82 Quantum TurboDiesel wagon (crushed)
'82 Quantum gasser (totaled by drunk driver)
'85 Quantum SW gasser (crushed)
-
- Cetane Booster
- Posts: 98
- Joined: Wed Mar 24, 2004 8:42 pm
- Location: cascade mountains, washington
Anyone tried to build a glow plug circuit that allows a little bit of 'afterglow' once the car starts? Maybe something that would have a lower voltage burn for a minute or so. Would this allow for a cleaner burn until the engine warms up?
I believe that some of the older Mercedes had this setup. And possibly the Isuzu/Chevy Luv trucks?
I believe that some of the older Mercedes had this setup. And possibly the Isuzu/Chevy Luv trucks?
'90 Ram 12V Cummins
'92 Jetta (current gas>TD swap project)
'86 Quantum Synchro SW gasser (future TD project?)
'82 Rabbit TurboDiesel Pickup (Totaled due to inattention)
'83 Quantum TurboDiesel sedan (crushed)
'82 Quantum TurboDiesel wagon (crushed)
'82 Quantum gasser (totaled by drunk driver)
'85 Quantum SW gasser (crushed)
'92 Jetta (current gas>TD swap project)
'86 Quantum Synchro SW gasser (future TD project?)
'82 Rabbit TurboDiesel Pickup (Totaled due to inattention)
'83 Quantum TurboDiesel sedan (crushed)
'82 Quantum TurboDiesel wagon (crushed)
'82 Quantum gasser (totaled by drunk driver)
'85 Quantum SW gasser (crushed)
Individual Wires
I installed a system with an individual wire to each glow plug. All wires run to the #4 glow plug. It is true there is VERY little room to install all the wires on that one glow plug along with the incoming power wire. The nut only goes about half way on.
I'll look into this "power distribution block" to allow for more room. I like the individual wires, it allows for a really quick resistance check to see which glow plug (if any) is broke.
Any help on this "power distribution block" would be appreciated.
I'll look into this "power distribution block" to allow for more room. I like the individual wires, it allows for a really quick resistance check to see which glow plug (if any) is broke.
Any help on this "power distribution block" would be appreciated.
-
- Hillbilly Tuner
- Posts: 2424
- Joined: Sat Mar 11, 2006 10:11 am
- Location: Near Lund B.C. Kanada.
EX Glowplug speaks up.
To by-pass VW wiring on 1980 to 1984 ---is Apple Pie --simple --if coke will post pictures of how hagar did it ? ---works like crazy --NEVER any problems.
Relay --(small Amerikan starter rely) is mounted on side of left front Tower.
hagar.
PS : VW setup is downright stupid.----wires under the dash with tons of amps ? --fire hazard. --IMHO.
Relay --(small Amerikan starter rely) is mounted on side of left front Tower.
hagar.
PS : VW setup is downright stupid.----wires under the dash with tons of amps ? --fire hazard. --IMHO.
VWs, at least in the '70s-'80s all had the "afterglow" feature, built in to the relay-timer. Edit... well, maybe not, come to think of it. at least the '77-'80 slow-glow systems DID have what you are calling the "afterglow" feature. The "fastglow" systems may not have.(?) Anyone have the definitive answer here?rayray wrote:Anyone tried to build a glow plug circuit that allows a little bit of 'afterglow' once the car starts? Maybe something that would have a lower voltage burn for a minute or so. Would this allow for a cleaner burn until the engine warms up?
I believe that some of the older Mercedes had this setup. And possibly the Isuzu/Chevy Luv trucks?
J.R.
SoCal
-
- Cetane Booster
- Posts: 33
- Joined: Thu Mar 23, 2006 1:25 pm
- Location: south-east michigan
GLOWPLUG REWIRE--HILLBILLY STYLE!
recently had glowplug problems AGAIN!
this time i used a ford starter relay-- with four terminals[$10 at autozone]---'ole time' horn button [$4 at autozone].
one side/end wired from the battery lug of the rabbit starter to the relay, the other side/end to the first accessable glowplug terminal, with 10 gauge thhn machine tool wire,[ soldered terminals].
i placed the 'ole time' horn button just to the left of the steering wheel. wired the horn button with heavy-duty 18 gauge speaker wire [very thick grey plastic outer insulation red and black insulated conductors inside] THIS FORD RELAY HAS TWO CONTROL CENTER TERMINALS [some have single center control center terminals] L@@K closely at the center terminals---one is labeled starter the other labeled ignition, chose the ignition terminal and the relay won't click/energize!
the 'ole style' horn button IS WIRED THIS WAY ..... power the horn button from the relay side/end lug fed from the battery of the rabbit starter [ i put a 15 fuse in-line to protect the 'ole time' horn button], the other to the control center terminal labeled 'starter'.
if this 'rigged-solution should fail i'll place a 50 amp r.v. blade in-line fuse 'before' the relay.
TURN THE IGNITION KEY---PUSH the 'ole time' horn button HEAR the click and KNOW the glowplug is getting FULL AMPERAGE!
the first diesel trucks i 'operated' had glowplug push buttons for cold starts.
I CONSIDERED A DIODE TO ELIMINATE BACKFEEDING THE 'ORIGINAL EQUIPMENT' GLOWPLUG RELAY-----BUT CHOSE THE CHEAPEST WAY!
TOO MANY ELECTRONIC RELAYS ALREADY --WHY ADD ANOTHER!
okay critique me! so far it works and it is soooo simple!
this time i used a ford starter relay-- with four terminals[$10 at autozone]---'ole time' horn button [$4 at autozone].
one side/end wired from the battery lug of the rabbit starter to the relay, the other side/end to the first accessable glowplug terminal, with 10 gauge thhn machine tool wire,[ soldered terminals].
i placed the 'ole time' horn button just to the left of the steering wheel. wired the horn button with heavy-duty 18 gauge speaker wire [very thick grey plastic outer insulation red and black insulated conductors inside] THIS FORD RELAY HAS TWO CONTROL CENTER TERMINALS [some have single center control center terminals] L@@K closely at the center terminals---one is labeled starter the other labeled ignition, chose the ignition terminal and the relay won't click/energize!
the 'ole style' horn button IS WIRED THIS WAY ..... power the horn button from the relay side/end lug fed from the battery of the rabbit starter [ i put a 15 fuse in-line to protect the 'ole time' horn button], the other to the control center terminal labeled 'starter'.
if this 'rigged-solution should fail i'll place a 50 amp r.v. blade in-line fuse 'before' the relay.
TURN THE IGNITION KEY---PUSH the 'ole time' horn button HEAR the click and KNOW the glowplug is getting FULL AMPERAGE!
the first diesel trucks i 'operated' had glowplug push buttons for cold starts.
I CONSIDERED A DIODE TO ELIMINATE BACKFEEDING THE 'ORIGINAL EQUIPMENT' GLOWPLUG RELAY-----BUT CHOSE THE CHEAPEST WAY!
TOO MANY ELECTRONIC RELAYS ALREADY --WHY ADD ANOTHER!
okay critique me! so far it works and it is soooo simple!
81 diesel caddy
93 volvo 240
68 triumph T120R
69 bsa A65L
93 volvo 240
68 triumph T120R
69 bsa A65L
I assume the power distribution block is out in the open so you don't have to get the continuity tester directly on each glow plug? I'm currently trying to figure out why my car won't start, and I wish it had this setup!rayray wrote:I wires each glow plug individually. I use a 'power distribution block' commonly used in car stereo amplifier application to tie them all together.
'84 Quantum turbodiesel wagon